6440A REV H Norge Washer Parts List

Replacement ice maker (sub r0156669)

This is a replacement ice maker assembly. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. Disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part. NOTE: This part has been updated by the manufacturer and does not include the cover, ice level arm or the wire harness. You can reuse those from the original ice maker.

Light bulb - 40w (sub 7407p103-60)

This 40-watt light bulb has a standard screw-in base. It is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Bucket auger (auger asm disp)

Dryer door switch (door switch assembly)

This 3-wire with leads dryer door switch is an on and off mechanism that prevents the dryer from operating while the door is open. The dryer will not operate until the door switch signals that the dryer door is closed. If the dryer won’t start, the lever broke off, or the switch shorted out, the appliance will not operate and the part will need to be replaced. This switch is a genuine OEM part and replaces the 2-wire switch. Please remember to disconnect the power to the dryer before starting the repair.

Drip bowl - 6 inch (sub 74001212)

This six-inch chrome drip bowl is intended for use with rolled terminal-style plug in surface element units. The drip bowl sits under the burner to catch anything that may spill over to make cleaning up spills quick. This is a genuine OEM part and is sold individually.

Thermal cut-off kit (use wpl 279816)

This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. This genuine OEM kit also includes flat heaters with jumper wires. Make sure to disconnect the power source to the dryer before beginning this repair.

Tub dampening strap (strap damping)

This part is used to support the tub and keep it in the center of the cabinet to reduce vibration. If your washer is making loud noises, or shakes or moves, one or more of the straps may have broken. It is recommended to replace all 4 tub dampening straps at the same time. This part is sold individually.

Dryer cycling thermostat (thermostat, internal-bias)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Round style oven igniter (oven bake or broil igniter, 2.5 to 3.0 amp. The igniter draws electrical current through the oven safety valve to open it.)

The round style oven igniter ignites the gas to light the oven burner to produce heat for your range. The igniter measures approximately 3 1/2” in length and the amperage range is 2.5 to 3.0. If the element has shorted out, no longer glowing, or glowing but only orange or red when it needs to be white, you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. This igniter can replace igniters for either the broil or bake burners; it does not replace the flat-style igniters. The igniter includes two high-temperature wire connectors. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

Rear drum support roller kit (use wpl 349241t)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Agitator repair kit (use wpl 285746)

This agitator repair kit is used to move the upper agitator and connects the base of the agitator with the agitator top mover. The kit is most commonly used if the top part of the agitator is not moving correctly but the bottom portion is. If your washer will not agitate or is noisy, you may need to replace the kit. The kit includes a medium cam, agitator dogs, bearing, thrust bearing washer, and a dust cap seal. Agitator grease is recommended for the repair, but it is not included with the agitator repair kit, it must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting your repair.

M series new style coil kit (sub 12001349)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

D-shaped knob clip (clip knob)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Control knob and clip - white (control knob white assembly)

This knob and clip set is an OEM replacement part for your washer or dryer. The knob accepts a D-shaped shaft and is sold individually.

Crisper drawer cover (cover pan low)

This crisper drawer cover has the drawer slides built into it to allow the crisper drawer to slide in and out. This model measures 24 1/2 inches long x 19 inches wide x 2 5/8 inches deep, is made of plastic and is white in color. If the cover becomes cracked or damaged, you will need to replace it. This is a genuine OEM part.